Two Structures
Rotary uses an eccentric roller in a cylinder — few parts, low cost. Scroll uses meshing fixed/orbiting scrolls forming continuous compression chambers — low leakage, low vibration.
Comparison
| Factor | Rotary | Scroll |
|---|---|---|
| Capacity | 200–1500W | 1000–5000W |
| COP | Med (2.2–2.8) | High (2.8–3.4) |
| Noise | Higher | 5–10dB lower |
| Life/cost | Med/low | Long/high |
Selection
- Small cabinets, cost-sensitive: choose rotary HCK series.
- High power, 24h duty, quiet: choose scroll.
- Scroll has fewer moving parts, better long-term reliability.
查看 HCK 机柜空调产品 或 联系昊诚工控 获取选型方案。
What to ask before the order is placed
Five questions rarely change the price and frequently change whether the cabinet still works in year six. Ask them at quotation stage, when they are still questions, rather than after commissioning, when they become arguments.
- At what ambient temperature, and at what supply voltage, is the quoted capacity valid?
- What is the measured airflow in cubic metres per hour, and what clearance does the condenser need to be installed with?
- What is the control accuracy, and what does the unit do if its own sensor fails? A unit that assumes a safe reading turns a five-minute wiring fault into a burned panel.
- What is the compliance documentation, and does the test report actually exist for the unit being quoted — not for a sibling model?
- What is the lead time on a replacement unit, given where the cabinet physically is?
Those five answers, written down and signed off at quotation, are usually worth more to the project than a few percentage points of extra capacity.
Energy, duty cycle and the ten-year view
Over a ten-year life the energy is typically a larger share of the total cost than the unit itself. That changes which comparison is worth making: not "which is cheaper to buy" but "which will this cabinet consume over a decade", taken from the duty cycle the site will actually see rather than from a catalogue point that assumes continuous running.
- A correctly sized unit cycles. Most of its life is spent at part load, not at its rated point, and that is where a compressor is most efficient.
- Two units at about 60 % each usually beat one at 120 %: they share the duty, they run staggered, and a failure degrades the cooling rather than removing it.
- A fouled condenser is worth roughly a fifth of the capacity, and considerably more on an energy basis, because the compressor fights a warmer surface all year.
- Monitoring that reports duty cycle is usually justified within two seasons, first through the maintenance visits that get avoided.
The counter-argument is first cost, and it is not weak. But the honest comparison is ten-year against ten-year, with the energy figure derived from the site's actual duty rather than from a datasheet assumption that suits the supplier.
Sizing, selection and what the datasheet does not say
The selection that survives a hot summer starts from total heat dissipation rather than from the nameplate rating of the equipment. A drive's nameplate is its output; the heat it puts into the cabinet is a few percent of that, and assuming otherwise is the most common way to oversize a system by a factor of ten.
The working method has four steps. First, list every component that generates heat and take its dissipation from the datasheet rather than from its rating. Second, add the envelope gain of the enclosure itself, which for a sealed cabinet in a hot climate is often the largest single term. Third, apply a safety factor once, to cover the uncertainty in the first two steps. Fourth, round to the nearest sensible unit, and check that the result leaves the unit running part of the time rather than flat out.
| Step | What you are solving | Common error |
|---|---|---|
| Component heat | What the equipment puts into the air inside | Using nameplate power instead of dissipation |
| Envelope gain | Heat from outside through the cabinet walls | Forgetting it on small sealed boxes |
| Safety factor | Uncertainty in the estimate | Applying it twice, or not at all |
| Installed capacity | Rounding to a real catalogue unit | Picking a unit that will run at 100 % duty |
Then ask the three questions that turn a calculation into a specification: what ambient was the quoted capacity measured at, what airflow does the unit need, and how much clearance does the condenser require. Specifications that answer all three tend to be honest about their capacity; specifications that answer none of them are describing a product rather than a performance figure.
Airflow, placement and sealing
A unit that is correctly sized can still fail to hold setpoint because of how the air moves inside the cabinet. The evaporator takes in whatever air is beside it. If the warm air leaving the equipment rises into that intake, the refrigerant has no cold surface to evaporate against and the controller sees a cabinet that will not cool, whatever the rating on the box.
The three symptoms to look for are familiar: the setpoint is reached at the bottom of the cabinet but never near the top, the compressor runs continuously while the panel reads close to ambient, and the unit's own intake temperature is close to the ambient.
- Mount high, where the warm air rises
- Fit a baffle so air passes across the full height of the equipment rather than around it
- Direct the discharge across the load, not down into the floor of the cabinet
- Seal the perimeter between the unit and the cabinet wall; an IP-rated cabinet with an unsealed unit is not an IP-rated cabinet
- Keep the intake grille clean and unobstructed; flow resistance at the intake quietly costs capacity
Measure the temperature spread from the bottom to the top of the cabinet after a full working day. A spread above 8 °C points at the airflow rather than the capacity, and it is a cheaper fault to fix than a larger unit.
Maintenance intervals that fit the site
There is no single correct interval. There is only an interval that is written down, and a filter and condenser that can be reached without dismantling the panel. What a unit in a clean air-conditioned plant room needs and what a unit under a machining centre needs are two different schedules.
| Environment | Filter | Condenser | Drain |
|---|---|---|---|
| Clean indoor plant room | Quarterly | Twice a year | Monthly |
| Workshop with dust or swarf | Monthly | Quarterly | Monthly |
| Outdoor coastal | Quarterly | Every two months | Monthly |
| Desert, sand-laden air | Monthly | Every two months | Monthly |
| Wash-down or high humidity | Monthly | Quarterly | Weekly |
Two habits do most of the work. The first is recording the ambient at each visit, which converts next year's argument about whether the unit has degraded into a settled question. The second is never pressure-washing a dry, dusty coil from the front, which drives the dust into the fins instead of shifting it. Clean dry first, rinse gently, and let it dry before the unit runs again.
Containerised and energy storage enclosures
These are the enclosures where the cooling has to work against a heat source that is inside the load rather than in the electronics. A battery pack generates heat in proportion to current, so the worst case is not a peak load in cool weather — it is a full-rate charge or discharge in the hottest ambient the site will see.
Unevenness matters more than the average. Cells at the top of a stack run hotter because hot air rises; cells at one end run hotter if the airflow never reaches them. Older cells in a mixed pack are also hotter than their neighbours, which ages the pack faster than the average temperature would suggest.
Because the cabinet has no drain point in a container sitting on bare ground, condensate needs a designed path rather than a drip tray. Because the unit sits inside a fire-sensitive volume, its air paths and materials are part of the fire strategy rather than an afterthought. And because the pack will outlive the cooling unit, the unit should be a replaceable item with a service path, which is a design decision that is cheap now and expensive later.